Diaper Cake Tutorial

Simpan kode iklan disini.

UPDATE:  check out my most recent diaper cake for some optional revisions to supplies and instructions.

I. Supplies Needed:


One large telescoping mailing tube (mine was 4 inches in diameter). I found mine at The Container Store.

You'll also need:

• a large piece of cardboard
• white butcher paper or wrapping paper
• doilies
• 2 bags clear rubber hair bands (think Goody) - about 100 bands
• large rubber bands, preferably white (I also found these at the container store - Can Bandz)
• a strong cardboard wrapping paper tube
  
• 2 packs of good-quality diapers, preferably plain white
• ribbon
• decorative paper
  
• safety pins
  
• a hot glue gun
• tape
• rubber cement
  
• sharp scissors
  
• flowers for decoration

• 

First, roll all of your diapers. I bought one pack of pampers newborns (up to 10 lbs) and one pack of size one diapers (8-14 lbs) - approximately 45 diapers total. My friend is having twins, so I thought the smaller diapers would fit better. Roll the diapers with the pattern on the inside and secure around the middle with a clear rubber band. The open end of the diaper should be rolled to the inside.

It will look like this. Continue until all the diapers are rolled and set aside.

II. The Diaper Cake Stand

Since I was planning to transport this diaper cake to work on the subway, I wanted it to be really sturdy. This method makes for a very solid cake.

1. Cut 3 large circles out of strong cardboard. For the largest tier, I traced a dinner plate. For the middle tier, I used a salad plate, and for the top tier, I traced a small bowl.

2. Trace each size again on white paper (I used wrapping paper so it had a nice shine). Cut the three circles out and glue (I used rubber cement) to the cardboard.


3. For a decorative edge, glue doilies around the circumference.


4. Now you are ready to start building the stand. First you will need to cut your mailing tube to the height of your rolled diapers. The larger sized diapers were about 4 inches tall when rolled, so I cut the outer (white) layer of the mailing tube to approximately 4 inches. Using a hot glue gun, glue the outer tube to the center of the decorative side of the lower tier.


5. Cut the inner (brown) tube to approximately 3-4 inches in length. Hot glue to the bottom (undecorated side) of the middle tier.



6. The middle tier will now slide into the bottom tier.


7. Repeat the process with the middle tier.


8. For the top tier, use a strong cardboard wrapping paper tube or something similar. Try to find a tube that does not easily bend (the inner tubes of saran wrap or reynolds wrap work well). Cut to the height of your smaller sized rolled diapers and hot glue it to the center of the decorated side of the top tier.


III. Adding the diapers

1. With the cake stand built, you are ready to start adding diapers. I disassembled my stand and added the diaper layers one tier at a time. Put the large rubber band around the mailing tube first, and it will secure the diapers as you add them. I used two layers of rolled diapers on the bottom tier.


2. The middle tier had a single row of rolled diapers.


3. The top tier also had a single row of rolled diapers.


4. I had extra diapers, so I put rolled diapers inside of the mailing tubes on the bottom and middle layers. This would also be a good place to hide other baby gifts (socks, receiving blankets, binkies, etc.) if you so choose. I also placed unrolled diapers around the mailing tubes to add few more. You can slide them into the middle there without removing the rolled layers.


III. Decoration

1. I taped green velum leaves to each of the cardboard bases to add a bit of interest to the edges


2. Use decorative ribbon to cover the rubberbands on each layer. I pinned one edge of the ribbon to the large white rubberband at the back of the diaper cake with a safety pin, so none of the diapers would be damaged. Then, I wrapped the ribbon around the diaper layer and overlapped it in the back, securing with hot glue (hopefully that makes sense). I love the look of double ribbon, but a single layer would do just as well.


3. Add a decorative cake topper. I used paper roses from a tutorial I saw at MarthaStewart.com. This trio of roses slid right into the opening of the wrapping paper tube in the top tier.


4. Place a few smaller flowers that match the topper on the lower layers. I just slid the wire stems in place under the cardboard base and used double sided tape on the bottom of the blossom to secure.


5. Sit back and enjoy all the oohs and ahhs at your baby shower.



Hopefully this tutorial was helpful! Sometimes I have a hard time putting crafty directions into words. This first-time diaper cake was a series of trial and error, but in the end had a great finished product. My favorite part of this diaper cake is that it is very sturdy, yet each of the tiers slide apart easily. It will easy for the mom-to-be to dissemble when it comes time to put those diapers to use, and the inner compartments are ideal for hiding additional gifts.

Enjoy!

Simpan kode iklan disini.

Bagikan ke Facebook